Volume and solids
NVW and VMC: How to Calculate Weight Solids and Volatile Matter in Paint
Published by Morex Technologies ·
NVW (non-volatile matter by weight, also called total solids by weight) is the percentage of a paint’s weight that remains after the volatiles evaporate. VMC (volatile matter content) is the percentage that evaporates. Together they always add up to 100 %.
NVW and VMC formulas
NVW (%) = Σ (wᵢ × sᵢ ÷ 100) ÷ Σ wᵢ × 100 VMC (%) = 100 − NVW
| Symbol | Meaning | Unit |
|---|---|---|
| wᵢ | Weight of raw material i | g |
| sᵢ | Solids content of raw material i by weight | % |
| NVW | Non-volatile matter by weight | % w/w |
| VMC | Volatile matter content | % w/w |
Worked example
| Raw material | Weight (g) | Density (g/cm³) | Solids (% w/w) | Solid density (g/cm³) |
|---|---|---|---|---|
| Acrylic emulsion (binder) | 30 | 1.05 | 50 | 1.15 |
| Titanium dioxide, rutile (pigment) | 20 | 4.10 | 100 | 4.10 |
| Calcium carbonate (extender) | 15 | 2.70 | 100 | 2.70 |
| Water | 35 | 1.00 | 0 | — |
| Total | 100 |
Solid weight = 30 × 0.50 + 20 × 1.00 + 15 × 1.00 + 35 × 0 = 50 g. NVW = 50 ÷ 100 × 100 = 50.0 %, and VMC = 100 − 50 = 50.0 %.
The same paint has a calculated SVR of 31.72 %. Weight solids are higher than volume solids here because the pigment and extender are much denser than the binder and water.
Example values are illustrative, chosen to show the arithmetic. Use the density, solids and oil absorption from your own raw materials’ technical data sheets.
Weight solids versus volume solids
NVW is easy to measure and is the usual batch control value. Volume solids (SVR) decide film build and coverage. Two paints with the same NVW can have very different SVR if one is filled with dense pigments, so compare like with like.
Binder solids content (BSC)
BSC (%) = Σ (w_resin × s_resin ÷ 100) ÷ Σ wᵢ × 100
| Symbol | Meaning | Unit |
|---|---|---|
| w_resin | Weight of each resin or binder as supplied | g |
| s_resin | Solids of that resin by weight | % |
In the example, binder solids are 30 × 0.50 = 15 g, so BSC = 15 %. Resin is supplied as a solution or emulsion, so always calculate with its solids, not its as-supplied weight. Here the pigment-to-binder ratio by weight is (20 + 15) ÷ 15 = 2.33 : 1.
Effect of adding water or solvent
Diluting the example with 5 g of water leaves the 50 g of solids unchanged but increases the total to 105 g, so NVW falls to 50 ÷ 105 × 100 = 47.62 % and VMC rises to 52.38 %.
How volatile content is measured
ASTM D2369 determines the weight percent volatile content of solvent-borne and water-borne coatings by heating a specimen (the standard condition is 110 ± 5 °C for 60 minutes); non-volatile content is found by difference. ASTM D2832 is a guide to choosing the right method for each type of coating. VMC includes water, so it is not the same as VOC content.
Common calculation mistakes
- Using the as-supplied weight of a resin solution as binder solids.
- Forgetting that water counts as volatile matter in VMC.
- Treating VMC as VOC — VOC excludes water and exempt compounds and is expressed per volume.
- Comparing NVW between paints with very different pigment densities and drawing conclusions about film build.
Frequently asked questions
What is NVW in paint and how is it calculated?
NVW is non-volatile matter by weight. Multiply each raw material’s weight by its solids fraction, add them up, divide by the total weight and multiply by 100.
How is volatile matter different from non-volatile matter?
Volatile matter (water and solvents) evaporates during drying; non-volatile matter (binder solids, pigments, extenders and non-volatile additives) forms the dry film. By weight, VMC = 100 − NVW.
How do I calculate binder solids from resin data?
Multiply the resin’s weight in the formulation by its solids content from the supplier’s data sheet. Divide by the total formulation weight and multiply by 100 for binder solids content.
What is the difference between weight solids and volume solids?
Weight solids is the share of the paint’s mass that stays in the film; volume solids is the share of its volume. Dense pigments make weight solids much higher than volume solids.
Calculating this in PaintOS
PaintOS calculates total volume, SVR, NVW, VMC, PVC and an estimated CPVC from the density, solids, solid density and oil absorption stored for each raw material, and recalculates them as a formulation changes.
Learn about PaintOS formulation management →