Volume and solids
How to Calculate SVR (Solids Volume Ratio) in Paint
Published by Morex Technologies ·
Solids volume ratio (SVR), also called volume solids, is the percentage of a wet paint’s volume that remains as dry film after the volatile components (water or solvent) evaporate. It is the volume of the non-volatile solids (ΣSV) divided by the total volume of the formulation, multiplied by 100.
The SVR formula
SVR (%) = ΣSV ÷ V × 100
| Symbol | Meaning | Unit |
|---|---|---|
| SVR | Solids volume ratio (volume solids) | % v/v |
| ΣSV | Total solid volume of all ingredients | cm³ |
| V | Total volume of the formulation | cm³ |
Both volumes are calculated from the formulation weights, so the result is a theoretical value. It assumes that the volumes of the ingredients simply add up (no volume change on mixing) and that all volatile material leaves the film.
Step 1: Volume of each raw material and total volume
Vᵢ = wᵢ ÷ ρᵢ V = Σ Vᵢ
| Symbol | Meaning | Unit |
|---|---|---|
| wᵢ | Weight of raw material i in the formulation | g |
| ρᵢ | Density of raw material i as supplied | g/cm³ |
| Vᵢ | Volume of raw material i | cm³ |
Total volume is the sum of every ingredient’s volume, including water and solvents. A volume balance check is simply confirming that the weights divided by densities add up to the total volume used in later calculations, and that no ingredient has a missing or zero density.
Step 2: Total solid volume (ΣSV)
SVᵢ = (wᵢ × sᵢ ÷ 100) ÷ ρs,ᵢ ΣSV = Σ SVᵢ
| Symbol | Meaning | Unit |
|---|---|---|
| sᵢ | Solids content of raw material i by weight | % |
| ρs,ᵢ | Density of the dry solids of raw material i | g/cm³ |
| SVᵢ | Solid volume contributed by raw material i | cm³ |
For a pigment or extender supplied as a dry powder, solids are 100 % and the solid density is the pigment density. For a resin solution or emulsion, the solid weight is the weight multiplied by its solids content, and its volume must use the density of the dry resin, not the density of the liquid as supplied. Water and solvents contribute no solid volume.
Worked example
| Raw material | Weight (g) | Density (g/cm³) | Solids (% w/w) | Solid density (g/cm³) |
|---|---|---|---|---|
| Acrylic emulsion (binder) | 30 | 1.05 | 50 | 1.15 |
| Titanium dioxide, rutile (pigment) | 20 | 4.10 | 100 | 4.10 |
| Calcium carbonate (extender) | 15 | 2.70 | 100 | 2.70 |
| Water | 35 | 1.00 | 0 | — |
| Total | 100 |
| Raw material | Volume Vᵢ (cm³) | Solid volume SVᵢ (cm³) |
|---|---|---|
| Acrylic emulsion | 30 ÷ 1.05 = 28.571 | (30 × 0.50) ÷ 1.15 = 13.043 |
| Titanium dioxide | 20 ÷ 4.10 = 4.878 | 4.878 |
| Calcium carbonate | 15 ÷ 2.70 = 5.556 | 5.556 |
| Water | 35 ÷ 1.00 = 35.000 | 0 |
| Total | V = 74.005 | ΣSV = 23.477 |
SVR = 23.477 ÷ 74.005 × 100 = 31.72 %. The same figures give the theoretical density of the wet paint: 100 g ÷ 74.005 cm³ = 1.351 g/cm³.
Example values are illustrative, chosen to show the arithmetic. Use the density, solids and oil absorption from your own raw materials’ technical data sheets.
SVR and NVV: calculated versus measured
NVV (non-volatile matter by volume) describes the same property as SVR, but the term is normally used for the measured value. ASTM D2697 determines the volume non-volatile matter of clear or pigmented coatings by weighing and measuring the volume of a coated stainless steel disk before and after the film is dried.
Calculated SVR and measured NVV rarely match exactly. Differences come from volume change on mixing, solvent retained in the film, pigment packing and porosity, and inaccurate raw material data. Treat calculated SVR as a formulation tool, and use a measured value when a data sheet or customer specification requires it.
Using SVR: film thickness and coverage
WFT = DFT × 100 ÷ SVR Theoretical coverage (m²/L) = 10 × SVR ÷ DFT
| Symbol | Meaning | Unit |
|---|---|---|
| DFT | Dry film thickness | µm |
| WFT | Wet film thickness to apply | µm |
| SVR | Volume solids | % |
For the example paint (SVR 31.72 %) and a target DFT of 40 µm: WFT = 40 × 100 ÷ 31.72 = 126.1 µm, and theoretical coverage = 10 × 31.72 ÷ 40 = 7.93 m²/L. Practical coverage is lower because of application losses; multiply by the expected transfer efficiency.
What changes SVR
- Adding water or solvent increases total volume without adding solids, so SVR falls. Adding 5 g of water to the example gives 23.477 ÷ 79.005 × 100 = 29.72 %.
- Replacing a resin with a higher-solids grade, or using more pigment and extender, increases ΣSV and raises SVR.
- A low SVR means a thinner dry film per coat and lower coverage; a high SVR gives more film build per coat, usually with higher viscosity to manage.
Common calculation mistakes
- Using the density of a resin solution or emulsion, instead of the density of its dry solids, when calculating solid volume.
- Leaving water out of the total volume when the formulation is supplied ready to use with that water in it.
- Treating a missing density as 1 or a missing solids value as 0 % or 100 % without noticing.
- Comparing a calculated SVR directly with a measured NVV from a data sheet without allowing for the differences above.
Frequently asked questions
What is the formula for solids volume ratio?
SVR (%) = total solid volume ÷ total formulation volume × 100, where each volume is calculated from weight ÷ density.
What is the difference between total volume and total solid volume?
Total volume includes every ingredient, including water and solvent. Total solid volume (ΣSV) includes only the volume of the non-volatile part that stays in the dry film.
How does SVR affect theoretical paint coverage?
Theoretical coverage in m²/L equals 10 × SVR ÷ DFT in µm, so coverage rises in direct proportion to SVR at a given dry film thickness.
Which standard is used to measure volume nonvolatile matter in coatings?
ASTM D2697 covers volume nonvolatile matter in clear or pigmented coatings. Check which edition your specification refers to.
Why might water be excluded from a formulation calculation?
Some calculations are made on the formulation before let-down water is added. If the paint is sold with that water in it, include it in total volume, otherwise SVR and coverage will be overstated.
Calculating this in PaintOS
PaintOS calculates total volume, SVR, NVW, VMC, PVC and an estimated CPVC from the density, solids, solid density and oil absorption stored for each raw material, and recalculates them as a formulation changes.
Learn about PaintOS formulation management →